The material analysis of the surface light source and the design and production of the flat light need to pay attention to it!

LED panel lights have a delicate identity in the lighting market. The LED panel light derived from LED backlight has uniform light, no glare and exquisite structure, which has been loved by many people.

The structure of the surface light source mainly includes the following materials :

1. Aluminum frame

Appearance structure, and main structure of LED heat dissipation: generally use AL6063, aluminum extrusion die, low initial cost input, beautiful surface treatment, good heat dissipation effect, and some manufacturers start to make die-casting frame, so IP level can be higher, and the sealing light is better. The overall appearance is beautiful, but the cost of the initial investment in the mold is higher.

Surface light source material composition analysis and flat lamp design and production considerations

2, diffusion plate

The light of the light guide plate is evenly dispersed, and the function of blocking the dots is also played. The diffuser board generally uses Acrylic 2.0 sheet or PC material. Acrylic has lower cost and light transmittance higher than PC. Acrylic brittle anti-aging performance is weak, PC price is slightly expensive, but anti-aging performance is strong. The diffuser plate cannot see the dots after being mounted, and the light transmittance is about 90%. The acrylic transmittance is 92%, and the PC is 88%. You can choose the diffuser material according to your needs, and generally use acrylic materials.

3, light guide plate

The side LED light is deflected by the dot refraction to change the angle of the light. The light guide plate is the heart of the flat light. The design of the dot is very important. The design of the dot is not good. The overall light effect is very poor. Generally, (1) the middle is bright and the two sides are dark; (2) the light edge has a bright edge. The middle is dark; (3) standing at different angles, the overall brightness is inconsistent; (4) the local dark area is obvious.

The light effect of the light guide plate is very large in the design of the dot, followed by the selection of the plate, but it is not right to pursue the brand of the brand. Because many brand manufacturers like Mitsubishi of Japan, most of the good plates are People order well, many Mitsubishi plates out of the market are mostly scraps, and their light transmittance is not as high as that of their own plates, so the choice of plates does not have to look at the manufacturers of the plates, as long as the test transmittance is high, the light effect is OK. In fact, it will be fine.

4, reflective paper

Reflecting the residual light on the back of the light guide. Usually RW250.

5, the rear cover

The sealed lamp body is generally Al aluminum, which has a strong overall texture and can provide a little heat dissipation.

6, LED light source

Generally used 3528, some people use 5630 and 5050, 5630 and 5050 are not efficient and the design of the dot is difficult, the versatility is poor, but the cost is low. The 3528 high-efficiency network has high versatility. Generally, it can be directly used to buy other light guides, and it is not necessary to re-sample the design.

7, the drive power

There are two kinds of power supply modes for lamp driver: (1) Direct use of cross current power supply, this mode has high efficiency, PF value is up to 0.95, cost-effective; (2) Constant pressure with cross-flow mode, stable performance, but low efficiency, high cost, generally The use of this mode is designed for customers who require certification, because the luminaire is a low-voltage luminaire with 24V input, no need to make safety regulations, and can be shipped to various countries by directly using a safety power supply.

Problems to be aware of in the design and production process

Surface light source material composition analysis and flat lamp design and production considerations

1, the thermal conductive adhesive should be as thin as possible, it is best to use the self-adhesive thermal adhesive, otherwise it will affect the thermal conductivity.

2, the choice of diffusing plate, nowadays, many flat-panel lamps on the market generally choose the diffusing plate with smooth surface and matte surface. This diffusing plate has a disadvantage, the static electricity is large, and it is easy to suck in the production process to produce bright spots, and In the long-term use, dust will enter the lamp body through various channels, which will cause the lamps to be densely colored. In the early days, some people used a diffused plate with double-sided diffusion. This diffusing plate has good light guiding effect and low static electricity, which can avoid the bright spot effect of dust entering the lamp body, but the diffusing plate has a low light transmittance of only 85-88%. Whether you choose this depends on the meaning of your own design.

3, LED selection, try to use high-efficiency lamps, because the side-emitting panel lights have limitations in heat dissipation and luminous flux output, power dissipation will have an impact, and low light efficiency.

4. When entering the glossy surface, do not stick glue when sticking the reflective paper. The glue will absorb light, and it is easy to appear on the light surface to produce bright edges. However, a large area of ​​the light guide plate needs to be glued a little, otherwise there will be a shadow strip because the reflective paper is not This is the case when it is tight and loose and warped in the lamp body.

Three major problems to be solved in the popularization of LED filament lamps

China IOT Conference Series [The 3rd China LED Intelligent Lighting Innovation Application Summit Forum ] will invite Zigbee Alliance, WiFi, Bluetooth and 2.4G technology major supplier executives to share their market insight and latest development results, I hope you can grasp This rare opportunity to exchange, find better business opportunities, and find a higher partner.

LED module introduction: LED Display Module is one of the main components of the finished Led Display! It mainly consists of LED lamp, PCB board, driver IC, resistor, capacitor and plastic kit!


Classification of Led Display Module


From the light color


LED display module is divided by color:


I. monochromatic modules, such as single red, single green, single blue, single yellow and single white modules


2. Two color modules, such as red and green, red and blue.


3. full color module is mainly a product with red, green and blue primary colors on one LED module

High Quality Module




According to the purpose of LED display


LED display module is divided into indoor, semi outdoor and outdoor, grid screen, strip screen, glass screen, etc. according to the different use space.


From the use of lamp beads


According to different LED packaging devices, LED display module can be divided into: LED display module of direct light, LED display module of indoor lattice, LED display module of surface mount.


Divide by pixel spacing


According to the LED pixel spacing, generally used more is: p1.25, p1.875, p1.56, P2, P3, P4, P5 and so on.

LED display function


1. Play the role of commodity publicity and attracting customers.


2. Play the role of store decoration and improve the level of enterprises.


3. Play the role of lighting and innovation.


4. Play the role of popularizing knowledge. (it can be used to play small information of enterprise products and knowledge of relevant industries)


5. Play the role of bulletin board. (promotion, recruitment information release)


6. Act as a foil to the atmosphere. Through the display screen, you can play the welcome words of superior leaders and various VIPs to visit and guide, and the celebration words of various major festivals.


7. It plays a warning role and is often used for road traffic LED navigation indication, etc.


It is undeniable that the ultimate purpose of establishing billboards is to publicize commodity information, attract target customers and make the most profit as much as possible. Led billboard is to achieve this goal to become the first choice of enterprise publicity.



LED Display Module

Led Display Module,Single Led Display Module,Soft Led Display Module,Flexible Led Display Module

Shenzhen Vision Display Technology Co,.LTD , https://www.ledvdi.com

Posted on